Bush Hog 175 10 Rear Mounted Blade OEM Parts
Bush Hog 175 10 Rear Mounted Blade Parts: Diagrams, Assemblies & Components
Bush Hog 175-10 Rear Mounted Blade FAQs, Specs, Maintenance & Installation Tips
If you’re running a 175-10 rear blade, this is your go-to reference for widths, setup, and safe grading. Find working specs, quick maintenance schedules, and troubleshooting advice for the most common tasks.
175-10 Rear Mounted Blade Fluid Specifications & Capacities
| Fluid | Specification | Capacity (qt) | Capacity (gal) |
|---|---|---|---|
| Grease | No. 2 lithium-based grease | As needed | As needed |
175-10 Rear Mounted Blade Complete Maintenance Schedule
| Service Item | Action | Interval | Part Number | Notes |
|---|---|---|---|---|
| All grease fittings (pivot points, cylinder pins, etc.) | Lubricate with No. 2 lithium grease | Every 8 hours | Use No. 2 lithium-based grease | |
| All bolts and nuts | Check tightness | Every 8 hours | Tighten as required | |
| Painted surfaces | Inspect and touch up | Every 8 hours | Touch up paint to prevent rust | |
| Unit (seasonal storage) | Clean debris, lubricate, touch up paint, store dry | End of season or long-term storage | - |
175-10 Rear Mounted Blade Operating Warnings
| System | Indicator | Required Action |
|---|---|---|
| Blade Contact | Bystanders within 300 feet | Keep all bystanders at least 300 feet away during operation |
Quick Jump
Tap a topic to jump to the answer.
- What is the working width of the Bush Hog 175-10 Rear Mounted Blade?
- What is the recommended tractor horsepower range for the 175-10 Rear Mounted Blade?
- What is the maximum angle adjustment for the blade?
- Can the blade be offset, and if so, by how much?
- What is the maximum tilt adjustment for the blade?
- What category hitch does the 175-10 use?
- What is the moldboard height of the blade?
- What is the moldboard thickness?
- How often should the pivot points be lubricated?
- What type of grease should be used for lubrication?
- What is the recommended procedure for seasonal storage?
- What should I do if the blade does not rotate or adjust properly?
- How do I adjust the blade angle?
- How do I check for blade wear?
- What is the cutting edge height?
- What is the cutting edge thickness?
- How do I replace the cutting edge?
- What is the maximum transport width of the blade?
- How do I troubleshoot uneven grading results?
- What safety precautions should be followed during operation?
What is the working width of the Bush Hog 175-10 Rear Mounted Blade?
Answer: The working width is 120 inches.
What is the recommended tractor horsepower range for the 175-10 Rear Mounted Blade?
Answer: The recommended tractor horsepower range is 70 to 125 HP.
What is the maximum angle adjustment for the blade?
Answer: The blade can be angled up to 45 degrees left or right.
Can the blade be offset, and if so, by how much?
Answer: Yes, the blade can be offset up to 49 inches left or right.
What is the maximum tilt adjustment for the blade?
Answer: The blade can be tilted up to 30 degrees up or down.
What category hitch does the 175-10 use?
Answer: The 175-10 uses a Category II or III 3-point hitch.
What is the moldboard height of the blade?
Answer: The moldboard height is 19.5 inches.
What is the moldboard thickness?
Answer: The moldboard thickness is 3/8 inch.
How often should the pivot points be lubricated?
Answer: Lubricate all pivot points every 8 hours of operation.
What type of grease should be used for lubrication?
Answer: Use a good quality lithium-based grease.
What is the recommended procedure for seasonal storage?
Answer: Clean all debris from the unit, lubricate all grease fittings, touch up paint on bare metal to prevent rust, and store in a dry location.
What should I do if the blade does not rotate or adjust properly?
Answer: Check for debris or damage at the pivot points and ensure all bolts are tightened and pivot points are lubricated.
How do I adjust the blade angle?
Answer: Remove the angle pin, rotate the blade to the desired angle, and reinsert the pin securely.
How do I check for blade wear?
Answer: Inspect the cutting edge regularly for excessive wear or damage and replace if necessary.
What is the cutting edge height?
Answer: The cutting edge height is 6 inches.
What is the cutting edge thickness?
Answer: The cutting edge thickness is 1/2 inch.
How do I replace the cutting edge?
Answer: Remove the mounting bolts, take off the worn cutting edge, position the new edge, and secure it with the bolts.
What is the maximum transport width of the blade?
Answer: The maximum transport width is 120 inches.
How do I troubleshoot uneven grading results?
Answer: Check for proper blade tilt, angle, and offset settings, and ensure the blade is not worn unevenly.
What safety precautions should be followed during operation?
Answer: Keep bystanders at least 300 feet away, operate at safe speeds, and ensure all adjustments are made with the tractor turned off and the blade lowered to the ground.