Woods 121Q-2 Multi-Spindle Cutter SN 10,001 & Up OEM Parts
Diagrams, Assemblies & OEM Parts for the Woods 121Q-2 Multi-Spindle Cutter
Woods 121Q-2 SN 10001 & Up Multi-Spindle Cutter FAQs, Specs, Maintenance & Installation Tips
Get answers to common questions and important maintenance information for your Woods 121Q-2 multi-spindle cutter. Learn about oil types, lubrication points, recommended operating practices, and essential safety instructions to keep your cutter running at peak performance.
121Q-2 SN 10001 & Up Fluid Specifications & Capacities
| Fluid | Specification | Capacity (qt) | Capacity (gal) |
|---|---|---|---|
| Gearbox Oil | SAE 80W-90 gear oil | -- | -- |
121Q-2 SN 10001 & Up Complete Maintenance Schedule
| Service Item | Action | Interval | Part Number | Notes |
|---|---|---|---|---|
| Gearbox Oil Level | Check oil level in all gearboxes; add oil as needed | Every 8 hr | ||
| Blade Spindle Bearings | Apply grease until fresh grease appears at seal | Every 8 hr | No. 2 lithium grease; 2 fittings | |
| Driveline U-joints and Guard Bearings | Grease all U-joints and guard bearings | Every 8 hr | No. 2 lithium grease; 4 U-joint fittings, 2 guard fittings | |
| Blades | Check for sharpness, damage, and secure mounting | Every 8 hr | Check part 31385, torque 450-500 ft-lbs | |
| Bolts and Fasteners | Check all hardware for tightness | Every 8 hr | ||
| Slip Clutch | Check for proper operation and adjust as needed | Every 8 hr | ||
| Gearbox Oil | Change oil in all gearboxes after first 50 hr, then every 250 hr | 250 hr | Use SAE 80W-90 gear oil |
121Q-2 SN 10001 & Up Operating Specifications
| Specification | Value |
|---|---|
| Working Width | 10 ft |
| Number of Blades | 2 |
| PTO Speed | 540 rpm |
| Tractor Requirement | 35–90 HP |
121Q-2 SN 10001 & Up Operating Warnings
| System | Indicator | Required Action |
|---|---|---|
| Blade Contact | Bystanders present | Keep bystanders at least 300 feet away during operation |
121Q-2 SN 10001 & Up Seasonal Storage Procedure
- Clean all debris from unit
- Lubricate all grease fittings
- Touch up paint on bare metal to prevent rust
- Store in dry location
Quick Jump
Tap a topic to jump to the answer.
- What is the recommended PTO speed for the Woods 121Q-2 Multi-Spindle Cutter?
- What is the minimum tractor horsepower required to operate the Woods 121Q-2?
- What is the cutting width of the Woods 121Q-2 Multi-Spindle Cutter?
- What is the recommended cutting height range for this cutter?
- How often should I check the gearbox oil level?
- What type of oil should be used in the gearbox?
- How frequently should the gearbox oil be changed?
- How often should I grease the blade spindle bearings?
- What type of grease is recommended for lubrication points?
- What category of three-point hitch is required for attachment?
- What is the maximum diameter of material that can be cut?
- How many blades does the Woods 121Q-2 have?
- What should I do if the blades become dull or damaged?
- How do I adjust the cutting height?
- What is the recommended procedure for seasonal storage?
- What should I do if the cutter vibrates excessively during operation?
- What safety precautions should be taken during operation?
- How do I transport the cutter safely?
- What should I do if the PTO shaft makes noise or vibrates?
- How do I troubleshoot poor cutting performance?
What is the recommended PTO speed for the Woods 121Q-2 Multi-Spindle Cutter?
Answer: The recommended PTO speed is 540 RPM.
What is the minimum tractor horsepower required to operate the Woods 121Q-2?
Answer: The minimum tractor horsepower required is 35 HP.
What is the cutting width of the Woods 121Q-2 Multi-Spindle Cutter?
Answer: The cutting width is 10 feet.
What is the recommended cutting height range for this cutter?
Answer: The recommended cutting height range is 2 to 12 inches.
How often should I check the gearbox oil level?
Answer: Check the gearbox oil level every 8 hours of operation.
What type of oil should be used in the gearbox?
Answer: Use SAE 80W-90 gear oil in the gearbox.
How frequently should the gearbox oil be changed?
Answer: Change the gearbox oil after the first 50 hours, then every 250 hours of operation.
How often should I grease the blade spindle bearings?
Answer: Grease the blade spindle bearings every 8 hours of operation.
What type of grease is recommended for lubrication points?
Answer: Use No. 2 lithium grease for all lubrication points.
What category of three-point hitch is required for attachment?
Answer: The cutter is compatible with Category II three-point hitches.
What is the maximum diameter of material that can be cut?
Answer: The maximum cutting capacity is 1.5 inches in diameter.
How many blades does the Woods 121Q-2 have?
Answer: The cutter is equipped with 4 blades.
What should I do if the blades become dull or damaged?
Answer: Replace or sharpen the blades as needed.
How do I adjust the cutting height?
Answer: Adjust the cutting height by repositioning the rear wheel and adjusting the tractor’s three-point hitch.
What is the recommended procedure for seasonal storage?
Answer: Clean all debris from the unit, lubricate all grease fittings, touch up paint on bare metal to prevent rust, and store in a dry location.
What should I do if the cutter vibrates excessively during operation?
Answer: Stop the machine and inspect for loose, damaged, or unbalanced blades. Repair or replace as necessary.
What safety precautions should be taken during operation?
Answer: Keep bystanders at least 300 feet away during operation and always operate with all shields in place.
How do I transport the cutter safely?
Answer: Raise the cutter to transport position, lock the transport locks, and use appropriate warning lights and slow-moving vehicle emblems.
What should I do if the PTO shaft makes noise or vibrates?
Answer: Stop operation and inspect the PTO shaft for damage or improper installation. Repair or replace as needed.
How do I troubleshoot poor cutting performance?
Answer: Check for dull or damaged blades, improper cutting height, excessive ground speed, or clogged discharge areas. Address any issues found.